Tips On How To Extend Smok Pen Recharge Time


Tips On How To Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was developed by two guys in California. They wished to develop a cool writing instrument that appeared as if a genuine pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.

smok pen

The Smok Pen includes a built quality that is just great. I found that even though it can be an electronic pen the build quality is simply as good as any of the pens that I have reviewed. It is because of how they made the very best cap. You don’t need to worry about the cap cracking or breaking you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. Generally the coil on a Smok Pen is bigger than on other pens. I believe that they did this on purpose, to help make the pen feel more substantial.

If you take a glance at a Smok Pen, you will notice that your body of the pen is round and not smooth like other pens. On the trunk of the pen you will find a little tab that houses the coil. When you press on the tab you can actually turn the heating element on and off. I must say i liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.

To use the Smok Pen you have to keep the heat button pressed. After the button is pressed, the heating element will start to warm up. Once it gets to the appropriate temperature you can turn off the JUUL Pods heating element. Smok recommends utilizing a 22mm tank. I prefer a more substantial tank, but that’s just me.

Once you put your Smok Pen in to the tank you will notice a indicator light seriously. The indicator light will remain green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids into the coil heads.

After you have completed this step, you should always check to see in case you are at the proper temperature for the coils to fire. Or even then you should turn the energy off and try again. When you are still not satisfied with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is exactly what I would call the “troubleshooting process” because sometimes things just usually do not work as they should. I would recommend that you perform the next two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.

Before you go any further you should remove the battery from your pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. When you have loosened this wire you can then access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.

Once you have placed the sub-ohm tank into the pen you need to then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the energy and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it back off. When you initially put the pen in to the microwave the electronic reading will show a low voltage protection setting. If this setting does not automatically get set then you should follow the on screen instructions.

Once the Smok Pen has reached the temperature that it needs to reach you should then connect both wires to the negative and positive on the positive post on the Smok unit. You should then connect the other end of the battery to the negative post on the negative side of the Smok unit. The final step is to connect the positive cable to underneath of the Smok’s on / off switch.

After all the components have been placed into the pen, you should turn the energy on. Following the first test run, you ought to be able to see the battery life indicator light come on. If you don’t see any sign of life from the Smok Pen, you should remove the battery from the pen and then replace it with a brand new one. For your convenience gleam green light that could be pressed in order to confirm the battery charging status. Once you have done these things and you also do not start to see the green light indicating charging, you should replace the battery.